| 982706001 Liebherr A912 Li Slewing Ring | Grease Speed Rating n1:2800 rpm; B:45.00 mm; d:75.000 mm; D:190.0000 mm; Fillet Radius rb:1.00 mm; Fillet Radius ra:2.50 mm; Basic Static Radial Load Rating Co:140000 N; Oil Speed Rating n2:4000 rpm; Basic Dynamic Radial Load Rating C:168000 N; |
| 982751301 Liebherr R900B Li Slewing Ring | Da max.:150 mm; Calculation factor Y1:0.66; Basic static load rating C0:170 kN; Calculation factor X:0.6; Calculation factor Y2:1.07; h:5 mm; Mass bearing:2 kg; Fatigue load limit Pu:6.3 kN; Calculation factor e:0.95; r0:0.5 mm; r1,2 min.:2 mm; Calculation factor Y0:0.58; d1 ≈:124 mm; D:160 mm; da min.:115 mm; D1 ≈:141 mm; Basic dynamic load rating C:135 kN; ra max.:2 mm; b:6.5 mm; Limiting speed:6700 r/min; |
| 933816501 Liebherr A934C Li Slewing Ring | d:8 mm; B:10 mm; Mass inner ring:0.0048 kg; r, r1,2 min.:0.3 mm; F:12 mm; |
| 933628601 Liebherr LH60 MT Slewing Ring | d1 ≈:1244 mm; Limiting speed:400 r/min; D1 ≈:1066 mm; Da max.:1138 mm; da min.:1172 mm; Basic dynamic load rating C:1010 kN; ra max.:4 mm; Minimum load factor A:5600; Reference speed:300 r/min; r1,2 min.:5 mm; d:1060 mm; Fatigue load limit Pu:112 kN; H:115 mm; Mass bearing (including seat washer where applicable):240 kg; Basic static load rating C0:10400 kN; D:1250 mm; |
| 983088401 Liebherr A954 Li Slewing Ring | Ca:68 mm; A1:100 mm; J7:35 mm; Q150°:230 kN; Oil seal:2 x TSN 316 U; Locating ring:2 x FRB 5/170; P55°:580 kN; P0°:450 kN; P180°:290 kN; Housing:SNL 519-616 RU; Cap bolt, size:M 16x90; P150°:230 kN; Mass housing:13.7 kg; P90°:350 kN; Q120°:400 kN; da:80 mm; Appropriate attachment bolt, size G:20 mm; Oil level, max.:49 mm; Q180°:200 kN; J6:317 mm; |
| 982751301 Liebherr R904 Slewing Ring | Tolerance shaft:e7; Permissible sliding velocity v max.:0.5 m/s; Tolerance housing:H7; a:5 mm; α:124 °; Coefficient of friction µ min.:0.08; Coefficient of friction µ max.:0.15; Specific dynamic load factor K:25 N/mm²; Specific static load factor K0:45 N/mm²; h:76.5 mm; B:100 mm; D:90 mm; Mass bushing:1.7 kg; Permissible sliding velocity v min.:0 m/s; d:75 mm; |
| 982855001 Liebherr R932 Li Slewing Ring | D1:127.7 mm; Calculation factor f1:1; Preload class B GB:460 N; d1:112.3 mm; r3,4 min.:0.6 mm; Calculation factor f:1.23; Preload class D GD:1840 N; Attainable speed for oil-air lubrication:14000 r/min; Static axial stiffness, preload class B:147 N/µm; Reference grease quantity Gref:10.5 cm³; Da max.:134 mm; Ball diameter Dw:12.7 mm; rb max.:0.6 mm; Calculation factor fHC:1; C2:4 mm; Attainable speed for grease lubrication:8500 r/min; |
| 982752701 Liebherr R954B Slewing Ring | Dynamic (Cr):6 mm; D:310 mm; B:109 mm; with cylindrical bore:900 min-1; Grease:2370 kN; d:200 mm; with tapered bore:1 200 min-1; Oil:218.260 kN; Pu:1250 kN; rs (min):2.1 mm; Static (Cor):11.1 mm; |
| 90205146 Liebherr R922 NLC Slewing Ring | Sealed Speed Rating n3:1400 rpm; Fillet Radius ra:2.00 mm; Accessories:Two Seals & Snap-Rin; Grease Speed Rating Open/Shielded n1:2000 rpm; d:180.000 mm; Basic Static Radial Load Rating Co:200000 N; D:280.0000 mm; Oil Speed Rating Open/Shielded n2:2600 rpm; B:46.00 mm; Basic Dynamic Radial Load Rating C:190000 N; |
| 982751901 Liebherr R914STD Slewing Ring | d:60.000 mm; Grease Speed Rating n1:3400 rpm; B:57.20 mm; Basic Static Radial Load Rating Co:95000 N; Fillet Radius ra:2.00 mm; Sealed Speed Rating n3:3400 rpm; Basic Dynamic Radial Load Rating C:121000 N; Accessories:One Seal & Snap-Ring; D:130.0000 mm; Oil Speed Rating n2:4500 rpm; |
| 982855001 Liebherr R934 Slewing Ring | H:147.637 mm; Pa:4.07 kN; P90°:23.6 kN; Housing:SAF 610; J min.:196.85 mm; A2:190.5 mm; Appropriate attachment bolt size G:0.625 in; P120°:14.2 kN; da:41.275 mm; Stabilizing ring:2 x SR-1610; R2:19.05 mm; P150°:12.9 kN; J max.:228.6 mm; Cap bolt:2 x 1/2-13 UNC; N1:19.05 mm; Initial grease fill:107.73 g; P60°:39.1 kN; Ca:50.8 mm; h:36.513 mm; L:269.875 mm; |
| 982853501 Liebherr A310 Slewing Ring | Basic Dynamic Radial Load Rating C:15900 N; Grease Speed Rating Open/Shielded n1:11000 rpm; Accessories:One Shield & Snap-Ri; Basic Static Radial Load Rating Co:10200 N; Fillet Radius ra:1.00 mm; Oil Speed Rating Open/Shielded n2:14000 rpm; d:20.000 mm; D:52.0000 mm; B:15.00 mm; |
| 982853501 Liebherr R312 Slewing Ring | Static axial stiffnes:790 N/µm; Required attachment bolt size (DIN 912):M6; N:6.8 mm; a:82 mm; Preload:1920 N; H1:19 mm; Mass bearing:0.7 kg; D:75 mm; r3,4 min.:0.6 mm; da min.:32 mm; J:58 mm; Frictional moment:0.4 N·m; Fatigue load limit Pu:2.2 kN; r1,2 min.:0.3 mm; Number of attachment bolts:7; Da max.:48 mm; D2:48.2 mm; Angle between holes in outer ring (Pitch) α:45 °; Static moment stiffness:200 N·m/mrad; |
| 982757401 Liebherr R974 Slewing Ring | P150°:77 kN; N1:28.575 mm; H:360.363 mm; S:4.763 mm; J max.:549.275 mm; End plug (suffix Y):EPR 18; R1:115.888 mm; Ca:119.812 mm; J1:107.95 mm; Bearing limiting speed:2000 r/min; Stabilizing ring:SR-34-0; Mass pillow block:132 kg; PG:1/4 NPT; Cap bolt:4 x 3/4-10 UNC; Da:309.999 mm; P60°:234 kN; J min.:492.125 mm; Initial grease fill:878.85 g; Eye bolt:2 x 3/8-16 UNC; Pa:56 kN; |
| 982751301 Liebherr A316 Li Slewing Ring | J min.:441.325 mm; Ca:89.789 mm; L:558.8 mm; Stabilizing ring:2 x 38151-38; Cap bolt, SAE grade:5; Housing:SAF 038 KA; P150°:78.3 kN; RG:3/4 NPT; h:47.625 mm; P90°:136 kN; A1:158.75 mm; Pa:40 kN; Labyrinth ring:2 x LOR 156; R2:33.337 mm; Da:289.999 mm; P120°:85.9 kN; Eye bolt:2 x 3/8-16 UNC; End plug (suffix Y):EPR 21; ba:69.85 mm; PG:1/4 NPT; |
| 982882001 Liebherr A310 Slewing Ring | B:49.21 mm; Accessories:Removable Metal Shie; D:120.0000 mm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:71500 N; Grease Speed Rating Open/Shielded n1:5600 rpm; Oil Speed Rating Open/Shielded n2:6700 rpm; Basic Static Radial Load Rating Co:45000 N; Sealed Speed Rating n3:3800 rpm; d:55.000 mm; |