| 90020064 Liebherr LH26 EC Slewing Ring | D:72.0000 mm; Fillet Radius ra:1.00 mm; Accessories:One Seal; Basic Dynamic Radial Load Rating C:39100 N; B:30.20 mm; Oil Speed Rating n2:8000 rpm; Basic Static Radial Load Rating Co:36500 N; Sealed Speed Rating n3:6000 rpm; Grease Speed Rating n1:6000 rpm; d:35.000 mm; |
| 982751301 Liebherr A900 B Slewing Ring | P60°:185 kN; Mass pillow block:47.2 kg; Cap bolt, SAE grade:5; J min.:336.55 mm; PG:1/4 NPT; A2:187.325 mm; R2:30.163 mm; P120°:72.5 kN; Da:215.001 mm; Labyrinth ring:2 x LOR 111; h:46.831 mm; A1:120.65 mm; End plug (suffix Y):EPR 14; Stabilizing ring:SR-24-20; N1:22.225 mm; S:4.763 mm; H1:133.35 mm; L:419.1 mm; Bearing limiting speed:3800 r/min; Pa:20.7 kN; |
| 933628601 Liebherr LH60 MT Slewing Ring | d1 ≈:1244 mm; Limiting speed:400 r/min; D1 ≈:1066 mm; Da max.:1138 mm; da min.:1172 mm; Basic dynamic load rating C:1010 kN; ra max.:4 mm; Minimum load factor A:5600; Reference speed:300 r/min; r1,2 min.:5 mm; d:1060 mm; Fatigue load limit Pu:112 kN; H:115 mm; Mass bearing (including seat washer where applicable):240 kg; Basic static load rating C0:10400 kN; D:1250 mm; |
| 982811501 Liebherr R964B Slewing Ring | Recommended diameter for attachment bolts, inch G:0.625 in; s1:32.6 mm; d:49.213 mm; Basic static load rating C0:23.2 kN; A1:21 mm; B:51.6 mm; J:111 mm; Recommended diameter for attachment bolts, mm G:16 mm; L:143 mm; Basic dynamic load rating C:29.6 kN; Housing material:Composite for food a; Db:114 mm; Thread grub screw G2:3/8-24 UNF; N:17 mm; Recommended tightening torque for grub screw:16.5 N·m; |
| 982811501 Liebherr R964 Li Slewing Ring | Housing:SAF 622; P60°:189 kN; da:101.6 mm; R1:79.375 mm; H:287.337 mm; J min.:371.475 mm; N1:25.4 mm; Initial grease fill:765.45 g; P90°:113 kN; J max.:406.4 mm; Bearing limiting speed:3600 r/min; h:63.5 mm; J1:82.55 mm; Ca:89.789 mm; A1:133.35 mm; Stabilizing ring:2 x SR-1622; Cap bolt:2 x 1-8 UNC; Cap bolt recommended tightening torque:1220 N·m; R2:36.513 mm; Pa:16.7 kN; |
| 90020064 Liebherr LH26 M Slewing Ring | r2 max.:1 mm; Dw:4 mm; r1,2 min.:0.3 mm; r1 max.:0.8 mm; Lw:15.8 mm; Mass needle roller:1.56 g; |
| 982853501 Liebherr A312 Li TCD Slewing Ring | d:20 mm; Coefficient of friction µ min.:0.05; B:30 mm; Tolerance housing:H7; D:28 mm; Coefficient of friction µ max.:0.1; Permissible sliding velocity v max.:5 m/s; Permissible sliding velocity v min.:0.25 m/s; Mass bushing:0.061 kg; Tolerance shaft:h8; Specific dynamic load factor K:10 N/mm²; Specific static load factor K0:20 N/mm²; |
| 90020064 Liebherr LH22 C Slewing Ring | l3 min.:57 mm; dk:80 mm; C1 max.:38 mm; l7 min.:68 mm; α:6 °; d:60 mm; N1 max.:38 mm; h1:150 mm; d4 max.:68 mm; Mass rod end:8.5 kg; Basic dynamic load rating C:245 kN; G:M 42x2; Basic static load rating C0:405 kN; B:44 mm; Tightening torque bolt with internal hexagon:160 N·m; d2 max.:160 mm; Size bolt with internal hexagon:M 16; Material constant KM:330; l4 max.:230 mm; Specific dynamic load factor K:100 N/mm²; |
| 982706001 Liebherr R922 Li Slewing Ring | Limiting speed:5000 r/min; A:25.8 mm; Mass bearing unit:0.68 kg; Recommended tightening torque for grub screw:4 N·m; R1:15.7 mm; Fatigue load limit Pu:0.28 kN; B:31 mm; Hexagonal key size for grub screw N:3.175 mm; A5:25.3 mm; L:85.7 mm; Housing:FYWR 504 Y; N:11.1 mm; A1:11.1 mm; Db1:55.4 mm; Thread grub screw G2:1/4-28 UNF; Basic dynamic load rating C:10.8 kN; Recommended diameter for attachment bolts, mm G:10 mm; |
| 90020064 Liebherr LH24 M Slewing Ring | ra max.:0.3 mm; D:16 mm; Da max.:14 mm; Limiting speed:50000 r/min; da max.:7.4 mm; r1,2 min.:0.3 mm; Basic dynamic load rating C:1.43 kN; Basic static load rating C0:0.63 kN; Calculation factor f0:11.8; da min.:7 mm; D2 ≈:13.4 mm; Mass bearing:0.0049 kg; B:5 mm; Reference speed:100000 r/min; Fatigue load limit Pu:0.027 kN; Calculation factor kr:0.03; d2 ≈:7.5 mm; d:5 mm; |
| 982751301 Liebherr A316 Li Slewing Ring | J min.:441.325 mm; Ca:89.789 mm; L:558.8 mm; Stabilizing ring:2 x 38151-38; Cap bolt, SAE grade:5; Housing:SAF 038 KA; P150°:78.3 kN; RG:3/4 NPT; h:47.625 mm; P90°:136 kN; A1:158.75 mm; Pa:40 kN; Labyrinth ring:2 x LOR 156; R2:33.337 mm; Da:289.999 mm; P120°:85.9 kN; Eye bolt:2 x 3/8-16 UNC; End plug (suffix Y):EPR 21; ba:69.85 mm; PG:1/4 NPT; |
| 969331201 Liebherr R944C Li Slewing Ring | Basic dynamic load rating C:15.6 kN; Calculation factor f2A:1; B:16 mm; Calculation factor f:1.08; d2:57.9 mm; Basic static load rating C0:10.6 kN; Da max.:75.4 mm; Preload class A GA:85 N; Calculation factor fHC:1.01; Calculation factor f0:8.2; Preload class B GB:250 N; d1:60.25 mm; r1,2 min.:1 mm; Number of balls z:21; rb max.:0.6 mm; ra max.:1 mm; D:80 mm; db min.:54.6 mm; Db max.:75.8 mm; Calculation factor f1:1; |
| 90020576 Liebherr R914 compact Slewing Ring | B:55.00 mm; Basic Static Radial Load Rating Co:173000 N; Oil Speed Rating Open/Shielded n2:3300 rpm; D:250.0000 mm; Accessories:One Seal; d:95.000 mm; Fillet Radius ra:3.00 mm; Basic Dynamic Radial Load Rating C:203000 N; Grease Speed Rating Open/Shielded n1:2700 rpm; Sealed Speed Rating n3:1900 rpm; |
| 982855001 Liebherr R932 Li TR Slewing Ring | Grease Speed Rating n1:14000 rpm; Fillet Radius ra:1.00 mm; Oil Speed Rating n2:19000 rpm; D:37.0000 mm; Basic Static Radial Load Rating Co:10200 N; Fillet Radius rb:0.60 mm; Basic Dynamic Radial Load Rating C:18200 N; B:24.00 mm; d:12.000 mm; |
| 982752101 Liebherr A944 Li Slewing Ring | Calculation factor Y1:1.5; Calculation factor Y0:1.45; d:330.302 mm; D:438.023 mm; T:254 mm; r3,4 min.:3.3 mm; Calculation factor Y2:2.2; Thrust factor K:1.29; Basic dynamic load rating C:3400 kN; Comparative radial load rating CF:720 kN; Fatigue load limit Pu:550 kN; D1 ≈:405 mm; r1,2 min.:1 mm; Calculation factor e:0.45; Comparative axial load rating CFa:158 kN; Design variant/feature:TQOSN/GWSI; |
| 982853501 Liebherr A310 Slewing Ring | Basic Dynamic Radial Load Rating C:15900 N; Grease Speed Rating Open/Shielded n1:11000 rpm; Accessories:One Shield & Snap-Ri; Basic Static Radial Load Rating Co:10200 N; Fillet Radius ra:1.00 mm; Oil Speed Rating Open/Shielded n2:14000 rpm; d:20.000 mm; D:52.0000 mm; B:15.00 mm; |